Designed for use in a variety of applications in the 70V/100V fixed installation market, where sonic quality and reliability are the highest priorities, the high performance T500-T & T1000-T use complimentary AB bipolar output stages, 2 combined with the unique MC current driven floating drive stage and conventional analogue level controls. The sound quality is maintained over a very wide range of load and temperature conditions. Sophisticated “side-chain” limiters prevent distortion and speaker damage, but are out-of-circuit until the onset of clipping. The control circuitry provides full protection against short circuits, DC and excessive temperature together with inrush current limiting and delayed “turn-on”.

Designed for the fixed installation market, the high performance stereo T500 features MC2 Audio’s complementary Class AB bipolar topology and the unique MC2 Audio current driven floating drive stage. T500 delivers over 375W into 4 ohms with both channels driven, and an 750W in bridge mode. Conventional analogue level controls help deliver the cleanest sound available coupled with ultra-high standards of reliability. The T-Series proprietary control and protection circuitry continuously checks for fault conditions including shorted outputs, DC on outputs, excessive temperature, and component failure. If such an event occurs the outputs are disconnected, saving expensive driver repair bills. Sophisticated ‘side chain’ limiters prevent distortion and speaker damage but are out-of-circuit until the onset of clipping. The control circuitry provides full protection against inrush current limiting with delayed power on. Low noise vari-speed fans are utilized to minimize mechanical noise, making the T Series an ideal choice for live theatre. Optional internal crossover cards available.

Designed for the fixed installation market, the high performance stereo T1000 features MC2 Audio’s complementary Class AB bipolar topology and the unique MC2 Audio current driven floating drive stage. T1000 delivers over 750W into 4 ohms with both channels driven, and an 1500W in bridge mode. Conventional analogue level controls help deliver the cleanest sound available coupled with ultra-high standards of reliability. The T-Series proprietary control and protection circuitry continuously checks for fault conditions including shorted outputs, DC on outputs, excessive temperature, and component failure. If such an event occurs the outputs are disconnected, saving expensive driver repair bills. Sophisticated ‘side chain’ limiters prevent distortion and speaker damage but are out-of-circuit until the onset of clipping. The control circuitry provides full protection against inrush current limiting with delayed power on. Low noise vari-speed fans are utilized to minimize mechanical noise, making the T Series an ideal choice for live theatre. Optional internal crossover cards available.

Designed for the fixed installation market, the high performance stereo T2000 features MC2 Audio’s complementary Class AB bipolar topology and the unique MC2 Audio current driven floating drive stage. T2000 delivers over 1150W into 4 ohms with both channels driven, and an 2300W in bridge mode. Conventional analogue level controls help deliver the cleanest sound available coupled with ultra-high standards of reliability. The T-Series proprietary control and protection circuitry continuously checks for fault conditions including shorted outputs, DC on outputs, excessive temperature, and component failure. If such an event occurs the outputs are disconnected, saving expensive driver repair bills. Sophisticated ‘side chain’ limiters prevent distortion and speaker damage but are out-of-circuit until the onset of clipping. The control circuitry provides full protection against inrush current limiting with delayed power on. Low noise vari-speed fans are utilized to minimize mechanical noise, making the T Series an ideal choice for live theatre. Optional internal crossover cards available.

Designed for the fixed installation market, the high performance four channel T4-250 features MC2 Audio’s complementary Class AB bipolar topology and the unique MC2 Audio current driven floating drive stage. T4-2500 delivers over 300W into 4 ohms with all channels driven, and an 600W in bridge mode. Conventional analogue level controls help deliver the cleanest sound available coupled with ultra-high standards of reliability. The T-Series proprietary control and protection circuitry continuously checks for fault conditions including shorted outputs, DC on outputs, excessive temperature, and component failure. If such an event occurs the outputs are disconnected, saving expensive driver repair bills. Sophisticated ‘side chain’ limiters prevent distortion and speaker damage but are out-of-circuit until the onset of clipping. The control circuitry provides full protection against inrush current limiting with delayed power on. Low noise vari-speed fans are utilized to minimize mechanical noise, making the T Series an ideal choice for live theatre. Optional internal crossover cards available.

Designed for use in a variety of applications in the 70V/100V fixed installation market, where sonic quality and reliability are the highest priorities, the high performance T500-T & T1000-T use complimentary AB bipolar output stages, 2 combined with the unique MC current driven floating drive stage and conventional analogue level controls. The sound quality is maintained over a very wide range of load and temperature conditions. Sophisticated “side-chain” limiters prevent distortion and speaker damage, but are out-of-circuit until the onset of clipping. The control circuitry provides full protection against short circuits, DC and excessive temperature together with inrush current limiting and delayed “turn-on”.

DPanel-8 is a programmable remote wall panel with eight buttons. It can be programmed to control gains, mutes, standby and recall memories on any Delta or DPA amplifier, as well as working with other DP4 and 5 Series processors and DC1048. It is powered directly from a DPA or Delta DSP amplifier, and uses the RS485 bus to ensure compatibility with all units. Buttons can be programmed to work in groups for memory recall, and the LED backlight colour can be chosen per button, as well as the repeat time for gain adjustments, with selectable step-size and max/min ranges. Night time backlighting and brightness are also adjustable, and additional commands can be controlled via IR remote. An isolated relay is also fitted offering control of external devices such as drapes/curtains or projector screens.

The Delta Series has been designed to combine incredible audio power and performance with ultra-flexible connectivity for both remote control and audio. Exemplary audio processing is assured through the use of XTA’s DSP platform, and power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. Powerful processing features, such as Dynmaic EQ, FIR filtering and Dante networking, work alongside unique enhancements including 4 local + 4 aux DSP channels, meaning a single Delta DSP amplifier can control a stereo 4-way system with no external processing. Accepting analogue, AES3 digital and optional Dante networked audio, the Delta DSP amplifiers can connect to any source and make it available over the network, as well as processing four additional channels with local analogue outputs to connect to non-DSP Delta amplifiers. These auxiliary processed outputs can also be fed onto the network, and used by non-DSP Delta amplifiers that have Dante cards fitted, or by any other Dante enabled device. Connectivity for remote control is covered by USB, Ethernet and RS485, with relay of either USB or Ethernet control via RS485 to work with legacy products. Configuration of the amplifier’s processing is through the industry standard AudioCore application, with tuning and monitoring of a network of Delta DSP amplifiers handled wirelessly by the dedicated DeltaDirect iPad app. With a range of power levels available in the Delta Series, the non-DSP amplifiers can be networked to a single Delta DSP model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between. Running cool in even the most difficult conditions, the D80-DSP can deliver 4x 2000 W into 4 ohms with all channels driven, and an substantial 2x 4000 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output. This power is maintained even with reduced mains voltages thanks to generous limiter headroom.

The Delta Series has been designed to combine incredible audio power and performance with future proofing via the inclusion of simple to use digital audio networking. Power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. Accepting analogue, or optional Dante networked audio, this extra connectivity means that the Delta Series non-DSP models can also be used in installation systems which already have a centralized DSP core but require the flexibility of being able to pick up multiple channels of audio from a network. With a range of power levels available in the Delta Series, the non-DSP amplifiers can be networked to a single Delta DSP model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between. Running cool in even the most difficult conditions, the D40-ND can deliver 4x 2000 W into 4 ohms with all channels driven, and an substantial 2x 4000 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output. This power is maintained even with reduced mains voltages thanks to generous limiter headroom.

The Delta Series has been designed to combine incredible audio power and performance with future proofing via the inclusion of simple to use digital audio networking. Power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. Accepting analogue, or optional Dante networked audio, this extra connectivity means that the Delta Series non-DSP models can also be used in installation systems which already have a centralized DSP core but require the flexibility of being able to pick up multiple channels of audio from a network. With a range of power levels available in the Delta Series, the non-DSP amplifiers can be networked to a single Delta DSP model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between. Running cool in even the most difficult conditions, the D40-ND can deliver 4x 1000 W into 4 ohms with all channels driven, and an substantial 2x 2400 W bridged (4R), with outstanding distortion and noise figures right up to maximum output. This power is maintained even with reduced mains voltages thanks to generous limiter headroom. Running cool in even the most difficult conditions, the D40-ND can deliver 4x 1000 W into 4 ohms with all channels driven, and an substantial 2x 2000 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output. This power is maintained even with reduced mains voltages thanks to generous limiter headroom.

Delta Series offers the assurance of the highest quality audio power amp technology with future proofing via the inclusion of simple to use digital audio networking. A rear panel switch allows the amplifier to accept either four channels of analogue audio or pic up four channels of networked audio , via Dante, which is then converted using 24 bit 96kHz DACs. Then, connect to a Delta DSP amplifier using a single CAT5 cable to realise a stereo 4 way system - no external processing required. Run bridged channel pairs or link adjacent inputs for total flexibility in either analogue or digital mode. Within this 1U chassis, the amplifier also features individual 70/100V line drive, an auto standby power mode (with wake-up < 1s), tuneable fans adaptable to different level/performance scenarios, and GPIO for remote control and monitoring. The amplifier also supports the back-up amplifier inputs as on the Delta 40, and has a PFC enabled universal mains supply for worldwide use.

The Delta Series has been designed to combine incredible audio power and performance with ultra-flexible connectivity for both remote control and audio. Exemplary audio processing is assured through the use of XTA’s DSP platform, and power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. Powerful processing features, such as Dynmaic EQ, FIR filtering and Dante networking, work alongside unique enhancements including 4 local + 4 aux DSP channels, meaning a single Delta DSP amplifier can control a stereo 4-way system with no external processing. Accepting analogue, AES3 digital and optional Dante networked audio, the Delta DSP amplifiers can connect to any source and make it available over the network, as well as processing four additional channels with local analogue outputs to connect to non-DSP Delta amplifiers. These auxiliary processed outputs can also be fed onto the network, and used by non-DSP Delta amplifiers that have Dante cards fitted, or by any other Dante enabled device. Connectivity for remote control is covered by USB, Ethernet and RS485, with relay of either USB or Ethernet control via RS485 to work with legacy products. Configuration of the amplifier’s processing is through the industry standard AudioCore application, with tuning and monitoring of a network of Delta DSP amplifiers handled wirelessly by the dedicated DeltaDirect iPad app. With a range of power levels available in the Delta Series, the non-DSP amplifiers can be networked to a single Delta DSP model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between. Running cool in even the most difficult conditions, the D40-DSP can deliver 4x 1000 W into 4 ohms with all channels driven, and an substantial 2x 2000 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output. This power is maintained even with reduced mains voltages thanks to generous limiter headroom.

The Delta Series has been designed to combine incredible audio power and performance with future proofing via the inclusion of simple to use digital audio networking. Power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. Accepting analogue, or optional Dante networked audio, this extra connectivity means that the Delta Series non-DSP models can also be used in installation systems which already have a centralized DSP core but require the flexibility of being able to pick up multiple channels of audio from a network. With a range of power levels available in the Delta Series, the non-DSP amplifiers can be networked to a single Delta DSP model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between. Running cool in even the most difficult conditions, the D40-ND can deliver 4x 2700 W into 4 ohms with all channels driven, and an substantial 2x 5400 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output. This power is maintained even with reduced mains voltages thanks to generous limiter headroom.

The Delta Series has been designed to combine incredible audio power and performance with future proofing via the inclusion of simple to use digital audio networking. Power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. Accepting analogue, or optional Dante networked audio, this extra connectivity means that the Delta Series non-DSP models can also be used in installation systems which already have a centralized DSP core but require the flexibility of being able to pick up multiple channels of audio from a network. With a range of power levels available in the Delta Series, the non-DSP amplifiers can be networked to a single Delta DSP model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between. Running cool in even the most difficult conditions, the D40-ND can deliver 2x 4600 W into 4 ohms with all channels driven, and an over 6000 W into 2.7 ohm loads, with outstanding distortion and noise figures right up to maximum output. This power is maintained even with reduced mains voltages thanks to generous limiter headroom.

Delta Series offers the assurance of the highest quality audio power amp technology with future proofing via the inclusion of simple to use digital audio networking. A rear panel switch allows the amplifier to accept either four channels of analogue audio or pic up four channels of networked audio , via Dante, which is then converted using 24 bit 96kHz DACs. Then, connect to a Delta DSP amplifier using a single CAT5 cable to realise a stereo 4 way system - no external processing required. Run bridged channel pairs or link adjacent inputs for total flexibility in either analogue or digital mode. Within this 1U chassis, the amplifier also features individual 70/100V line drive, an auto standby power mode (with wake-up < 1s), tuneable fans adaptable to different level/performance scenarios, and GPIO for remote control and monitoring. The amplifier also supports the back-up amplifier inputs as on the Delta 40, and has a PFC enabled universal mains supply for worldwide use.

The Delta Series has been designed to combine incredible audio power and performance with ultra-flexible connectivity for both remote control and audio. Exemplary audio processing is assured through the use of XTA’s DSP platform, and power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. Powerful processing features, such as Dynmaic EQ, FIR filtering and Dante networking, work alongside unique enhancements including 4 local + 4 aux DSP channels, meaning a single Delta DSP amplifier can control a stereo 4-way system with no external processing. Accepting analogue, AES3 digital and optional Dante networked audio, the Delta DSP amplifiers can connect to any source and make it available over the network, as well as processing four additional channels with local analogue outputs to connect to non-DSP Delta amplifiers. These auxiliary processed outputs can also be fed onto the network, and used by non-DSP Delta amplifiers that have Dante cards fitted, or by any other Dante enabled device. Connectivity for remote control is covered by USB, Ethernet and RS485, with relay of either USB or Ethernet control via RS485 to work with legacy products. Configuration of the amplifier’s processing is through the industry standard AudioCore application, with tuning and monitoring of a network of Delta DSP amplifiers handled wirelessly by the dedicated DeltaDirect iPad app. With a range of power levels available in the Delta Series, the non-DSP amplifiers can be networked to a single Delta DSP model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between. Running cool in even the most difficult conditions, the D100-DSP can deliver 4x 2700 W into 4 ohms with all channels driven, and an substantial 2x 5400 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output. This power is maintained even with reduced mains voltages thanks to generous limiter headroom.

The TLine is a passive transformer chassis that can be loaded with up to for channels worth of impedance matching transformes. These can be mixed and matched in a variety of power handling capabilities and are designed to operate with 100V/70V/50V systems. Transformers are available with 250W, 500W and 750W into 100V/70V/50V. Each channels input Speakon connector takes the output connections from the amplifier and a corresponding connector carries the high voltage output from the channels transformer. To prevent saturation of the transformer core, amplifier channels shoud be fitted with high pass filters. All MC2 amplifiers can be fitted with optional crossover cards, or have internal jumper links for this purpose.

Designed for use in the best studio monitoring environment, but equally at home in any application where transparency and “no compromise“ performance are the focus, the S1400 delivers the sound quality and reliability expected from MC2. S1400 delivers over 1500W into 4 ohms with both channels driven, and an 3000W in bridge mode. S1400 utilises the best complimentary AB bipolar output stages, combined with the unique MC2 current driven floating drive stage along with analogue level controls for minimal signal degradation. Sophisticated “side-chain” limiters prevent distortion and speaker damage, but are out-ofcircuit until the onset of clipping so do not compromise the signal path under normal working conditions. A bespoke high fidelity shielded toroidal power supply combined with intelligent low noise fan control provide optimum conditions for the output stages, ensuring the only thing you will ever hear is your sound. Critical parts have been selected through a series of listening tests for optimum sonic performance and approved by some of the most well respected personnel in the industry. The amplifiers of course include full DC, thermal and short circuit protection to ensure trouble-free service.

Designed for use in the best studio monitoring environment, but equally at home in any application where transparency and “no compromise“ performance are the focus, the S800 delivers the sound quality and reliability expected from MC2. S800 delivers over 950W into 4 ohms with both channels driven, and an 1900W in bridge mode. S800 utilises the best complimentary AB bipolar output stages, combined with the unique MC2 current driven floating drive stage along with analogue level controls for minimal signal degradation. Sophisticated “side-chain” limiters prevent distortion and speaker damage, but are out-ofcircuit until the onset of clipping so do not compromise the signal path under normal working conditions. A bespoke high fidelity shielded toroidal power supply combined with intelligent low noise fan control provide optimum conditions for the output stages, ensuring the only thing you will ever hear is your sound. Critical parts have been selected through a series of listening tests for optimum sonic performance and approved by some of the most well respected personnel in the industry. The amplifiers of course include full DC, thermal and short circuit protection to ensure trouble-free service.