XTA Electronics
Sort by:
EOL
XTA Electronics
DPA80
The DPA Series has been designed to combine incredible audio power and performance with ultra-flexible connectivity for both remote control and audio. Exemplary audio processing is assured through the use of XTA’s DSP platform, and power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. DPA80 delivers over 2000W into 4 ohms per channels, and an 2x 4000W in bridge mode.
Accepting analogue, AES3 digital and optional Dante networked audio, the DPA Series can connect to any source and make it available over the network, as well as processing four additional channels with local analogue outputs to connect to non-DSP amplifiers. These auxiliary processed outputs can also be fed onto the network, and used by non-DSP DNA Series (and MC2 Delta Series) amplifiers that have Dante cards fitted, or by any other Dante enabled device.
Connectivity for remote control is covered by USB, Ethernet and RS485, with relay of either USB or Ethernet control via RS485 to work with legacy products. Configuration of the amplifier’s processing is through the industry standard AudioCore application, with tuning and monitoring of a network of DPA and Delta DSP amplifiers handled wirelessly by the dedicated DeltaDirect iPad app.
With a range of power levels available in the DPA Series, the non-DSP amplifiers can be networked to a single DPA model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between.
XTA Electronics
GQ600
The GQ600 us a precision dual channel 1/3 octave graphic equaliser which provides up to 10dB of boost or cut at 30 centre frequencies between 25Hz and 20kHz. Filter design has been carefully optimised for good interpolation and improved narrow band performance, whilst high quality long-throw 45mm sliders are used for better resolution.
The GQ600 also provides excellent noise and distortion performance, with a flat noise figure of better than-98dBm.
A shelving HF Trim section is provided, with adjustable gain and frequency allowing fast adjustments to be made to overall high frequency response. This obviates the need for system re-voicing when, for example, changes in humidity or audience size occur.
A sweepable high-pass filter offers turnover frequencies of 10Hz to 150Hz and a fixed frequency low-pass filter is also provided for increased H.F. driver protection. This filter is selectable in or out of circuit via jumper links on the main circuit board.
Audio inputs and outputs are provided on lockable XLRs and are fully electronically balanced as standard. Optional transformer balancing is also available for both inputs and outputs.
Additional features include; relay fail-safe bypass, peak level indicators and optional Perspex security cover.
The GQ600 is sturdily constructed from high quality components and undergoes extensive testing and quality control procedures including a minimum 48 hours burn-in period prior to despatch.
EOL
XTA Electronics
DNA20-4T100V
The DNA Series offers the assurance of XTA’s highest quality audio power amp technology with future proofing via the inclusion of simple to use digital audio networking.
Fast rear panel switching allows the amplifier to accept either four channels of analogue audio or pick up four channels of networked audio, via Dante, which is then converted using 24 bit 96kHz DACs.
Connect to an DPA amplifier using a single CAT5 cable to realise a stereo 4 way system with no further external processing required. Switch back to analogue to use as a powerful traditional quad channel amplifier. Run bridged channel pairs or link adjacent inputs for total flexibility in either analogue or digital mode.
Within this 1U chassis, the DNA20 also features individual 70/100V line drive, an auto-standby power mode (with near-instant wake-up at
EOL
XTA Electronics
DNA120
The DNA Series offers the assurance of XTA’s highest quality audio power amp technology with future proofing via the inclusion of simple to use digital audio networking.
Accepting analogue, or optional Dante networked audio, this extra connectivity means that the all DNA models can also be used in installation systems which already have a centralized DSP core but require the flexibility of being able to pick up multiple channels of audio from a network.
With a range of power levels available in the DNA Series, the amplifiers can be networked to a single DPA model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between.
Running cool in even the most difficult conditions, the DNA40 can deliver 2x 4600 W into 4 ohms with all channels driven, and an over 6000 W into 2.7 ohm loads, with outstanding distortion and noise figures right up to maximum output.
productBadge.normal
XTA Electronics
DP648-D
The DP648 builds on the legacy of the SIDD, C2, D2 processing, the XTA DP448 and DPA amplifiers. Providing ethernet control of this suite of IIR, FIR and dynamic processing essential for sound system management. The Dante/ AES67 option and flexible routing make it a comprehensive system processor, for overall system management or for traditional loudspeaker management.
The DP648 works as a system processor for any audio system, the XTA system scales for more advanced control when partnered with other XTA products. This includes the MX36 console/source switcher, DPA and DNA amplifiers which come with or without dsp.
The DP648 is equally suited to FOH racks as a system processor providing overall system management or located in amplifier racks as a more traditional crossover providing stereo 2, 3, 4+ way loudspeaker processing. The extensive XTA preset library makes this even easier.
To deliver this precise control the DP648 has the full suite of classical IIR filters, phase, all pass and delay on both inputs and outputs, input dynamic eq and an extensive loudspeaker preset library containing both IIR and FIR setting .
The DP648 has full front panel control, PC remote software control by Audiocore Amped edition. PC & MacOS control using globcon XTA MC² Edition. Full or partial locking of front controls is possible when required.
Multiple DP648s can be elegantly controlled by fast software grouping, inputs and or outputs can appear in up to 32 groups, making complex systems easy to manage. Grouping is effectively a virtual 32 output processor across compatible amplifiers and processors.
EOL
XTA Electronics
DNA80
The DNA Series offers the assurance of XTA’s highest quality audio power amp technology with future proofing via the inclusion of simple to use digital audio networking.
Accepting analogue, or optional Dante networked audio, this extra connectivity means that the all DNA models can also be used in installation systems which already have a centralized DSP core but require the flexibility of being able to pick up multiple channels of audio from a network.
With a range of power levels available in the DNA Series, the amplifiers can be networked to a single DPA model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between.
Running cool in even the most difficult conditions, the DNA40 can deliver 4x 2000 W into 4 ohms with all channels driven, and an substantial 2x 4000 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output.
XTA Electronics
DS8000
The DS8000 is a 2U, 8 input to 32 output mic/line distribution system with 16 transformer balanced isolated outputs, and 16 electronically balanced outputs fitted as standard. Input transformers and replacement of the electronically balanced outputs with transformer balanced outputs are available as options.
Featuring microphone pre-amps designed by Gottelier award winning Alex Cooper, the DS8000 offers many facilities including a dual redundant power supply, simple Outside Broadcast “one to many” split switching and 48V “safe“ functions to prevent tampering.
Subtle panel lighting for dark under-stage environments and the option of adding an ADC card for integration into digital networks, plus bespoke new output transformers all combine to produce a flexible, rugged high quality distribution system.
EOL
XTA Electronics
DPA100
The DPA Series has been designed to combine incredible audio power and performance with ultra-flexible connectivity for both remote control and audio. Exemplary audio processing is assured through the use of XTA’s DSP platform, and power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. DPA100 delivers over 2700W into 4 ohms per channels, and an 2x 7000W in bridge mode.
Accepting analogue, AES3 digital and optional Dante networked audio, the DPA Series can connect to any source and make it available over the network, as well as processing four additional channels with local analogue outputs to connect to non-DSP amplifiers. These auxiliary processed outputs can also be fed onto the network, and used by non-DSP DNA Series (and MC2 Delta Series) amplifiers that have Dante cards fitted, or by any other Dante enabled device.
Connectivity for remote control is covered by USB, Ethernet and RS485, with relay of either USB or Ethernet control via RS485 to work with legacy products. Configuration of the amplifier’s processing is through the industry standard AudioCore application, with tuning and monitoring of a network of DPA and Delta DSP amplifiers handled wirelessly by the dedicated DeltaDirect iPad app.
With a range of power levels available in the DPA Series, the non-DSP amplifiers can be networked to a single DPA model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between.
EOL
XTA Electronics
DPA40
The DPA Series has been designed to combine incredible audio power and performance with ultra-flexible connectivity for both remote control and audio. Exemplary audio processing is assured through the use of XTA’s DSP platform, and power amplifier capabilities are taken care of with high efficiency output stages and a generous power supply. DPA40 delivers over 1000W into 4 ohms per channels, and an 2x 2000W in bridge mode.
Accepting analogue, AES3 digital and optional Dante networked audio, the DPA Series can connect to any source and make it available over the network, as well as processing four additional channels with local analogue outputs to connect to non-DSP amplifiers. These auxiliary processed outputs can also be fed onto the network, and used by non-DSP DNA Series (and MC2 Delta Series) amplifiers that have Dante cards fitted, or by any other Dante enabled device.
Connectivity for remote control is covered by USB, Ethernet and RS485, with relay of either USB or Ethernet control via RS485 to work with legacy products. Configuration of the amplifier’s processing is through the industry standard AudioCore application, with tuning and monitoring of a network of DPA and Delta DSP amplifiers handled wirelessly by the dedicated DeltaDirect iPad app.
With a range of power levels available in the DPA Series, the non-DSP amplifiers can be networked to a single DPA model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between.
EOL
XTA Electronics
DNA40
The DNA Series offers the assurance of XTA’s highest quality audio power amp technology with future proofing via the inclusion of simple to use digital audio networking.
Accepting analogue, or optional Dante networked audio, this extra connectivity means that the all DNA models can also be used in installation systems which already have a centralized DSP core but require the flexibility of being able to pick up multiple channels of audio from a network.
With a range of power levels available in the DNA Series, the amplifiers can be networked to a single DPA model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between.
Running cool in even the most difficult conditions, the DNA40 can deliver 4x 1000 W into 4 ohms with all channels driven, and an substantial 2x 2000 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output.
productBadge.normal
XTA Electronics
DP648
The DP648 builds on the legacy of the SIDD, C2, D2 processing, the XTA DP448 and DPA amplifiers. Providing ethernet control of this suite of IIR, FIR and dynamic processing essential for sound system management. The Dante/ AES67 option and flexible routing make it a comprehensive system processor, for overall system management or for traditional loudspeaker management.
The DP648 works as a system processor for any audio system, the XTA system scales for more advanced control when partnered with other XTA products. This includes the MX36 console/source switcher, DPA and DNA amplifiers which come with or without dsp.
The DP648 is equally suited to FOH racks as a system processor providing overall system management or located in amplifier racks as a more traditional crossover providing stereo 2, 3, 4+ way loudspeaker processing. The extensive XTA preset library makes this even easier.
To deliver this precise control the DP648 has the full suite of classical IIR filters, phase, all pass and delay on both inputs and outputs, input dynamic eq and an extensive loudspeaker preset library containing both IIR and FIR setting .
The DP648 has full front panel control, PC remote software control by Audiocore Amped edition. PC & MacOS control using globcon XTA MC² Edition. Full or partial locking of front controls is possible when required.
Multiple DP648s can be elegantly controlled by fast software grouping, inputs and or outputs can appear in up to 32 groups, making complex systems easy to manage. Grouping is effectively a virtual 32 output processor across compatible amplifiers and processors.
XTA Electronics
Dpanel-8
DPanel-8 is a programmable remote wall panel with eight buttons. It can be programmed to control gains, mutes, standby and recall memories on any Delta or DPA amplifier, as well as working with other DP4 and 5 Series processors and DC1048. It is powered directly from a DPA or Delta DSP amplifier, and uses the RS485 bus to ensure compatibility with all units.
Buttons can be programmed to work in groups for memory recall, and the LED backlight colour can be chosen per button, as well as the repeat time for gain adjustments, with selectable step-size and max/min ranges. Night time backlighting and brightness are also adjustable, and additional commands can be controlled via IR remote.
An isolated relay is also fitted offering control of external devices such as drapes/curtains or projector screens.
EOL
XTA Electronics
DNA20
The DNA Series offers the assurance of XTA’s highest quality audio power amp technology with future proofing via the inclusion of simple to use digital audio networking.
Fast rear panel switching allows the amplifier to accept either four channels of analogue audio or pick up four channels of networked audio, via Dante, which is then converted using 24 bit 96kHz DACs.
Connect to an DPA amplifier using a single CAT5 cable to realise a stereo 4 way system with no further external processing required. Switch back to analogue to use as a powerful traditional quad channel amplifier. Run bridged channel pairs or link adjacent inputs for total flexibility in either analogue or digital mode.
Within this 1U chassis, the DNA20 also features individual 70/100V line drive, an auto-standby power mode (with near-instant wake-up at
EOL
XTA Electronics
DNA100
The DNA Series offers the assurance of XTA’s highest quality audio power amp technology with future proofing via the inclusion of simple to use digital audio networking.
Accepting analogue, or optional Dante networked audio, this extra connectivity means that the all DNA models can also be used in installation systems which already have a centralized DSP core but require the flexibility of being able to pick up multiple channels of audio from a network.
With a range of power levels available in the DNA Series, the amplifiers can be networked to a single DPA model, creating a powerful, efficient system that’s easy to expand and adapt for use in live, install and everything in between.
Running cool in even the most difficult conditions, the DNA40 can deliver 4x 2700 W into 4 ohms with all channels driven, and an substantial 2x 5400 W bridged (8 ohms), with outstanding distortion and noise figures right up to maximum output.
