The U-Bracket design allows for either vertical or horizontal wall/ceiling mounting of an CFA-2HTH speaker. It is designed for a high safety margin and is made of 316grade (marine-grade) stainless steel that is compatible with both marine/ocean front and cruise ship applications, as well as direct weather inland applications and indoor installations.

The One Systems SP.PMT is a deluxe pole mount bracket with tilt capability designed for use with One Systems models ONE.SP6, ONE.SP8, ONE.SP12D and ONE.SP12T loudspeakers. The SP.PMT is made of structural steel with a dual-layer, zinc-rich powder coating that will provide long useful life and safety. The SP.PMT may be used on round or square poles. For square / rectangular poles, the minimum flat dimension must be 95.25 mm at the speaker’s mounting height and for round poles, the minimum diameter is 101.6 mm at the speaker’s mounting height. It provides a “tilt” angle range from vertical (0 degrees) to a maximum down tilt of 35 degrees. The tilt angle is adjustable in 13.3-degree increments.

The One Systems SP.PMK is a basic pole mount bracket designed for use with One Systems models ONE.SP6, ONE.SP8, ONE.SP12D and ONE.SP12T loudspeakers. The SP.PMK is made of structural steel with a dual-layer, zinc-rich powder coating that will provide long useful life and safety. The SP.PMK may be used on round or square poles. For square / rectangular poles, the minimum flat dimension must be 95.25 mm at the speaker’s mounting height and for round poles, the minimum diameter is 101.6 mm at the speaker’s mounting height.

The One Systems SL.PMT is a deluxe pole mount bracket with tilt capability designed for use with One Systems ONE.SL12 and ONE.SL15 loudspeakers. It is made of structural steel with a dual-layer, zincrich powder coating that will provide long useful life and safety. The SL.PMT may be used on round poles with a minimum flat dimension of 254 mm and provides a “tilt” angle range from vertical (0 degrees) to a maximum down tilt of 35 degrees. The tilt angle is adjustable in 5 degree increments.

The ONE SYSTEMS® PT-38/M is a pan and tilt bracket designed for use with the a variety of ONE SYSTEMS sound reinforcement enclosures. The design utilizes 316-grade stainless steel for use in ocean front and cruise ship environments and is may be used in inland direct weather environments as well. All components of the PT38/M are constructed of high quality 316-grade stainless steel and are suitable for outdoor permanent installation. The ONE SYSTEMS PT38/M provides a “tilt” angle range from vertical (0 degrees) to a maximum down tilt of 35 degrees. The tilt angle is adjustable in 13.3 degree increments. The “pan” angle varies from on axis to 40 degrees either side of the longitudinal axis in 13.3 degree increments. The PT38/M is designed for use with the 108HTH, 108HTC and 208HTC enclosures. The PT38/M is designed for flat surface mounting only.

The ONE SYSTEMS PT10/M is a pan and tilt bracket designed for use with a variety of ONE SYSTEMS sound reinforcement enclosures. All components of the PT10/M are constructed of high quality 316 stainless steel and durable resin and are suitable for outdoor permanent installation, as well as for indoor applications. The PT10/M may be used in ocean front and marine environments as well as inland direct weather applications. The ONE SYSTEMS PT10/M provides a “pan and tilt” angle range from vertical (0 degrees) in 10 degrees increments. There are two center pieces supplied and each center piece is capable of 20 degree increments in both pan and tilt axis rotations. The second center piece has its locating “teeth” rotated 10 degrees from the first center piece and may be interchanged to provide the required aiming precision within the 10 degree step resolution. The PT10/M is designed for use with the 104HTH and 106HTH enclosures.

The ONE SYSTEMS® PT-38/M is a pan and tilt bracket designed for use with the a variety of ONE SYSTEMS sound reinforcement enclosures. The design utilizes 316-grade stainless steel for use in ocean front and cruise ship environments and is may be used in inland direct weather environments as well. All components of the PT38/M are constructed of high quality 316-grade stainless steel and are suitable for outdoor permanent installation. The ONE SYSTEMS PT38/M provides a “tilt” angle range from vertical (0 degrees) to a maximum down tilt of 35 degrees. The tilt angle is adjustable in 13.3 degree increments. The “pan” angle varies from on axis to 40 degrees either side of the longitudinal axis in 13.3 degree increments. The PT38/M is designed for use with the 108HTH, 108HTC and 208HTC enclosures. The PT38/M is designed for flat surface mounting only.

The ONE SYSTEMS PT10/M is a pan and tilt bracket designed for use with a variety of ONE SYSTEMS sound reinforcement enclosures. All components of the PT10/M are constructed of high quality 316 stainless steel and durable resin and are suitable for outdoor permanent installation, as well as for indoor applications. The PT10/M may be used in ocean front and marine environments as well as inland direct weather applications. The ONE SYSTEMS PT10/M provides a “pan and tilt” angle range from vertical (0 degrees) in 10 degrees increments. There are two center pieces supplied and each center piece is capable of 20 degree increments in both pan and tilt axis rotations. The second center piece has its locating “teeth” rotated 10 degrees from the first center piece and may be interchanged to provide the required aiming precision within the 10 degree step resolution. The PT10/M is designed for use with the 104HTH and 106HTH enclosures.

The One Systems ONE.SP12DTM is a weather-protected 12 two-way horn-loaded sound projector solution suitable for professional audio applications indoors or for inland environments outdoors. The system’s transducers include a 12 woofer with a 3 voice coil and a 3 compression driver with a pure titanium diaphragm coupled to a large-sized 60° x 40° horn. Thanks to its 600 watt continuous power handling and high sensitivity, the ONE.SP12D provides high acoustic output capability, tremendous projection and installation flexibility in a reasonably-sized package. The ONE.SP12D’s enclosure is made of strong, UV-resistant, molded High Density Polyethylene (HDPE). Its specially built components and use of stainless steel suspension hardware ensure long useful life and safety for direct weather applications. An optional pole mount bracket is also available for customized mountingsolutions. This speaker is also available with an internal 400 W, 3-tap autoformer (ONE.SP12T). The ONE.SP12D provides high vocal intelligibility and tremendous acoustic output capability from its compact enclosure. Its large compression driver with titanium diaphragm delivers extended response with excellent transients and permits a lower crossover frequency for a more coherent sound. Its large-sized horn provides precise pattern control and long projection capability. The woofer’s specially treated cone and surround provide superior resonance damping and resistance against moisture and dry rot. The ONE.SP12D’s high power handling and sensitivity provides 130 dB continuous, 136 dB peak output capability.

The One Systems ONE.SL15 is a weather protected, directradiating 15 two-way loudspeaker solution for professional audio applications indoors or for inland uses outdoors. The system’s direct-radiating transducers include a 15 woofer with a 3 voice coil and a compression driver with a 2.5 pure titanium diaphragm coupled to a large rotatable 60° x 40° horn. Itsone-piece rotomolded enclosure is made of UV resistant High-Density Polyethylene (HDPE) with internal steel reinforcements for added strength. The enclosure is ported to enhance its low frequency performance. The ONE.SL15’s input section features an input weather cover with an IP 68-rated gland nut and its barrier strip has stainless steel hardware. The enclosure has 10 x M10 integrated stainless steel rigging points, which can be used in conjunction with the included U-Bracket for mounting to walls or ceilings. An optional pole mount bracket is also available for additional installation flexibility. The ONE.SL15 provides high vocal intelligibility with wide response capability from its reasonably-sized enclosure. Ist compression driver with pure titanium diaphragm delivers extended response and its long-throw horn is rotatable to facilitate horizontal or vertical placement for added flexibility. The woofer’s specially treated cone and surround provide excellent acoustic damping, moisture resistance and protection against dry rotting. The ONE.SL15’s vented enclosure and premium components provide 126 dB continuous, 132 dB peak output capability with wide frequency response and excellent transients for precise vocals and accurate music reproduction.

The One Systems ONE.SP8 is a weather protected, horn-loaded medium format speaker. Its one-piece rotomolded enclosure is made of UV resistant, High-DensityPolyethylene (HDPE). The enclosure is ported to aid low frequency extension, and its 8 woofer is horn-loaded to achieve higher output than would otherwise be possible. The enclosure is equipped with 5 x M8 stainless steel rigging points, which can be used in conjunction with the included U-Bracket for mounting to walls or ceilings. A 35 mm / 1-3/8 speaker pole socket is also provided for temporary setups. The grille is made from CNC punched structural steel and is coated in a two-layer zinc rich, UV resistant powder coat finish.The system’s 8 woofer has a specially-treated cone that resists moisture and dry rotting. Its high-energy ferrite magnet ensures high output for maximum coverage. Its medium-format HF driver is equipped with a titanium diaphragm and is coupled to a large-mouthed horn that provides excellent projection and superb pattern control. When pole mounting is required, an optional pole mount kit is also available. The ONE.SP8 provides high vocal intelligibility and tremendous acoustic output capability from its compact enclosure. Its 1.75 compression driver with titanium diaphragm delivers extended response with good transients and permits a lower crossover frequency for a more coherent sound. Its wide dispersion horn provides a big wide sound with good “throw” capability. The woofer’s specially treated cone and surround provide superior resonance damping that improves its sound quality. The ONE.SP8 can deliver 119 dB of continuous output using its 150 W tap at 70 or 100 volts.

The One Systems ONE.SP12TTM is a weather-protected 12 two-way horn-loaded sound projector with an internal autoformer suitable for professional audio applications indoors or for inland environments outside. The system’s transducers include a 12 woofer with a 3-inch voice coil and a 3 compression driver with a pure titanium diaphragm coupled to a large-sized 60° x 40° horn. The ONE.SP12T includes an internal 400 W, 3-tap autoformer (with Hi-Z taps at 400, 200 and 100 W at 70 or 100 volts) and it can also be powered as a Lo-Z (8 ohm) system. Thanks to its power handling and sensitivity, the ONE.SP12T provides high acoustic output capability, tremendous projection and installation flexibility in a reasonably-sized package. The ONE.SP12T’s enclosure is made of strong, UV-resistant High Density Polyethylene (HDPE). Its specially built components and use of stainless steel suspension hardware ensure long useful life and safety for direct weather applications. An optional pole mount bracket is also available for customized mounting solutions. This speaker is also available as a Lo-Z (8 ohm) system without autoformer (ONE.SP12D). The ONE.SP12T provides high vocal intelligibility and tremendous acoustic output capability from its compact enclosure. Its large compression driver with titanium diaphragm delivers extended response and permits a lower crossover frequency for more coherent sound. Its large-sized horn provides precise pattern control and long “throw” capability. The woofer’s specially treated cone and surround provide superior resonance damping and resistance against moisture and dry rot. The ONE.SP12T delivers 129 dB of continuous output using its 400 W tap at 70 or 100 volts.

The One Systems ONE.SP6 is a weather protected, horn-loaded small-format speaker. Its one-piece rotomolded enclosure is made of strong, UV resistant High-Density Polyethylene (HDPE). It's enclosure is ported to aid low frequency extension, and its 6.5 coax driver is horn-loaded to achieve higher output than would otherwise be possible. The enclosure is equipped with 3 x M8 stainless steel rigging points, which can be used in conjunction with the included U-Bracket for mounting to walls or ceilings. A 35 mm / 1-3/8 speaker pole socket is also provided for temporary setups. The grille is made from CNC punched structural steel and is coated with a two-layer zinc rich, UV resistant powder coat finish.The system’s coax driver has a specially-treated cone that resists moisture and dry rot. Its high-energy ferrite magnet ensures high output for maximum coverage. Its HF driver is equipped with a titanium diaphragm and is coupled to a short horn that provides good projection with superb pattern control. When pole mounting is required, an optional pole mount kit is also available. The ONE.SP6 provides high vocal intelligibility and impressive acoustic output capability from its small-sized enclosure. Its 1.34 compression driver with titanium diaphragm delivers extended response with precise transients and it permits a lower crossover frequency for a smoother more coherent sound. Its coaxially-mounted HF driver and horn provides a big sound with surprising “throw” capability from its small-size enclosure. The ONE.SP6 can deliver 115 dB of continuous output with a 150 W input.

The One Systems ONE.SL12 is a weather protected, directradiating 12 two-way loudspeaker solution for professional audio applications indoors or for inland uses outdoors. The system’s direct-radiating transducers include a 12 woofer with a 3 voice coil and a compression driver with a 2.5 pure titanium diaphragm coupled to a large rotatable 60° x 40° horn. Ist one-piece rotomolded enclosure is made of UV resistant High-Density Polyethylene (HDPE) with internal steel reinforcements for added strength. The enclosure is ported to enhance low frequency performance. The input section features an input weather cover with an IP 68-rated gland nut and its barrier strip has stainless steel hardware. The enclosure has 10 x M10 integrated stainless steel rigging points, which can be used in conjunction with the included U-Bracket for mounting to walls or ceilings. An optional pole mount bracket is also available for additional installation flexibility. The ONE.SL12 provides high vocal intelligibility with wide response capability from its reasonably-sized enclosure. Ist large-sized compression driver with pure titanium diaphragm delivers extended response with accurate transients. The long-throw horn is rotatable to facilitate horizontal or vertical placement for added flexibility. The woofer’s specially treated cone and surround provide moisture resistance, protection against dry rotting as well as excellent acoustic damping. The ONE.SL12’s vented enclosure and premium transducers provide 124 dB continuous, 130 dB peak output capability with wide frequency response and excellent transients for precise vocals and accurate music reproduction.

ONE SYSTEMS® offers a wide variety of enclosures that are compatible with M8 forged shoulder “eye” bolt suspension. ONE SYTEMS offer a complete kit that consists of 4 forged shoulder eye bolts and all necessary additional hardware. Each eye bolt is made of 316 (marine) grade stainless steel and is suitable for both outdoor permanent installation and indoor applications.

ONE SYSTEMS® offers a wide variety of enclosures that are compatible with M10 forged shoulder “eye” bolt suspension. ONE SYTEMS offer a complete kit that consists of 4 forged shoulder eye bolts and all necessary additional hardware. Each eye bolt is made of 316 (marine) grade stainless steel and is suitable for both outdoor permanent installation and indoor applications.

The ONE SYSTEMS PT76/M is a pan and tilt bracket designed for use with a variety of ONE SYSTEMS sound reinforcement enclosures. All components of the PT76/M are constructed of high quality 316-grade stainless steel and are suitable for outdoor permanent installation in ocean front and cruise ship environments and for general inland direct weather installations. The ONE SYSTEMS PT76/M provides a “tilt” angle range from vertical (0 degrees) to a maximum down tilt of 35 degrees. The tilt angle is adjustable in 5 degree increments. The “pan” angle varies from on axis to 40 degrees either side of the longitudinal axis in 13.3 degree increments. The PT76/M is designed for use with the 112HTH, 212HC, 312HC, 118HSB and CFA-2HTH enclosures. The PT76/M is designed for flat surface mounting only. If pole mounting is required, the PM4/M should be used.

The ONE SYSTEMS PT76/M is a pan and tilt bracket designed for use with a variety of ONE SYSTEMS sound reinforcement enclosures. All components of the PT76/M are constructed of high quality 316-grade stainless steel and are suitable for outdoor permanent installation in ocean front and cruise ship environments and for general inland direct weather installations. The ONE SYSTEMS PT76/M provides a “tilt” angle range from vertical (0 degrees) to a maximum down tilt of 35 degrees. The tilt angle is adjustable in 5 degree increments. The “pan” angle varies from on axis to 40 degrees either side of the longitudinal axis in 13.3 degree increments. The PT76/M is designed for use with the 112HTH, 212HC, 312HC, 118HSB and CFA-2HTH enclosures. The PT76/M is designed for flat surface mounting only. If pole mounting is required, the PM4/M should be used.

The PM4/M was designed to mount many of ONE SYSTEMS loudspeaker enclosures to a wide variety of pole diameters. The PM4/M is constructed of 316-grade stainless steel and is designed for use in ocean front and cruise ship environments as well as inland direct weather installations. The PM4/M will accommodate pole diameters from 10 inches (254mm) or larger. It is necessary to consult the pole manufacturer prior to installation to insure safe operating limits based on the pole construction, local wind patterns, and compliance with local and national codes. The PM4/M was designed to be used with the ONE SYSTEMS 112HTH, 212HC, 312HC, 118HSB and CFA-2HTH loudspeaker enclosures. The system consists of a pole mounting bracket that includes a tilting function. The tilt function allows down tilt, in 5 degree increments, from 0 degrees to a maximum down tilt of 35 degrees. The PM4/M is designed for pole mounting only.

The One Systems PM2/M is a 316-grade stainless steel pole mount system designed for pole mounting. The minimum rectangular or square pole face dimension is 3.75 inches (92mm). The minimum circular pole diameter is 4-inches (101.6mm). The PM2/M is designed to be used with the One Systems 104HTH or 106HTH loudspeaker systems only.

The ONE SYSTEMS® PM3-M is a pan and tilt bracket designed for use with the a variety of ONE SYSTEMS sound reinforcement enclosures. The PM3/M is made with 316 grade stainless steel and was designed for use in ocean front and cruise ship environments and may be used in inland direct weather environments as well. It is designed for use on square/rectangular poles. All components of the PM3/M are constructed of high quality 316 grade stainless steel and are suitable for outdoor permanent installation. The ONE SYSTEMS PM3/M provides a “tilt” angle range from vertical (0 degrees) to a maximum down tilt of 35 degrees. The tilt angle is adjustable in 13.3 degree increments. The “pan” angle varies from on axis to 40 degrees either side of the longitudinal axis in 13.3 degree increments. The PM3/M is designed for use with the 108HTH, 108HTC and 208HTC enclosures. The PM3/M is designed for pole mounting only.

The PM4/M was designed to mount many of ONE SYSTEMS loudspeaker enclosures to a wide variety of pole diameters. The PM4/M is constructed of 316-grade stainless steel and is designed for use in ocean front and cruise ship environments as well as inland direct weather installations. The PM4/M will accommodate pole diameters from 10 inches (254mm) or larger. It is necessary to consult the pole manufacturer prior to installation to insure safe operating limits based on the pole construction, local wind patterns, and compliance with local and national codes. The PM4/M was designed to be used with the ONE SYSTEMS 112HTH, 212HC, 312HC, 118HSB and CFA-2HTH loudspeaker enclosures. The system consists of a pole mounting bracket that includes a tilting function. The tilt function allows down tilt, in 5 degree increments, from 0 degrees to a maximum down tilt of 35 degrees. The PM4/M is designed for pole mounting only.

The ONE SYSTEMS® PM3-M is a pan and tilt bracket designed for use with the a variety of ONE SYSTEMS sound reinforcement enclosures. The PM3/M is made with 316 grade stainless steel and was designed for use in ocean front and cruise ship environments and may be used in inland direct weather environments as well. It is designed for use on square/rectangular poles. All components of the PM3/M are constructed of high quality 316 grade stainless steel and are suitable for outdoor permanent installation. The ONE SYSTEMS PM3/M provides a “tilt” angle range from vertical (0 degrees) to a maximum down tilt of 35 degrees. The tilt angle is adjustable in 13.3 degree increments. The “pan” angle varies from on axis to 40 degrees either side of the longitudinal axis in 13.3 degree increments. The PM3/M is designed for use with the 108HTH, 108HTC and 208HTC enclosures. The PM3/M is designed for pole mounting only.

The One Systems Cross Field Array-2HTH (CFA-2HTH) was designed to provide very high intelligibility and acoustic output where long throw requirements are specified. The enclosure features all 316 (marine) grade stainless steel rigging. The grill assembly and all other fasteners are 304 -grade stainless steel that feature a newly developed coating system allowing the CFA-2HTH to be used in ocean front and marine environments, as well as inland direct weather environments. The CFA-HTH is a nominal 55 degree horizontal by 30 degree array that features a fully rotatable high frequency horn/waveguide. This allows the CFA-2HTH to be used in either a vertical or horizontal orientation and still allows the desired coverage patterns. The high-frequency configuration consists of two large-format, close-spaced compression drivers coupled to a 2” (50.8mm) constant directivity horn. The low-frequency configuration consists of 4 bandwidth optimized 10” (254mm) diameter woofers in a 2 x 2 array. The CFA-2HTH is ideal for both outdoor/direct weather long throw applications and indoor applications in high ambient noise environments. Typical applications are football and soccer fields, baseball fields and large theme park environments. Indoor environments such as basketball and hockey arenas are also well very appropriate venues for the CFA-2HTH, due to the ultra- high system intelligibility. In order to achieve maximum system performance the CFA-2HTH should be high-pass filtered using a 4th order (24dB/octave) high-pass filter set to 80Hz. This filter frequency can be set using any high-quality DSP based loudspeaker processor. The CFA-2HTH is a direct weather design that features a three-layer stainless steel grille assembly. The enclosure design is a laminated fiberglass construction with high safety factory structural rigging points molded in the enclosure shell. The system is also compatible with the One Systems Pole Mount System PM4/M where vertical tilt requirements are specified in a pole mount application. The One Systems PT7/6M is also compatible with the CFA-2 HTH when pan and tilt are both required. The PT76/M is suitable for flat surface mounting only. The CFA-2HTH has an internal 600-watt autoformer and an internal jumper system that allows the enclosure to be used in either a “Lo Z” (4-ohm) or “Hi Z” configuration. The autoformer taps are 600 watts, 300 watts, and 150 watts. The input will allow for either 70.7Vrms operation or 100Vrms operation. The autoformer is a very low insertion loss (